Brake System

ABS Sensor

AAASTAND® ABS sensors are engineered using automotive-grade Hall-effect or magnetic-inductive elements, high-temperature resistant wiring, and corrosion-proof housings. precision-molded connectors, reinforced signal cables, and optimized sensing heads for accurate wheel-speed detection. AAASTAND® sensors deliver precise wheel-speed feedback for ABS, ESP, TCS, and advanced driver-assistance systems. Available in active Hall sensors, passive inductive sensors, integrated harness assemblies, and versions with built-in tone rings.

Brake Booster

AAASTAND® brake boosters use high-strength stamped steel housings, premium EPDM rubber diaphragms, and precision-calibrated check valves. a corrosion-resistant e-coating or powder-coated finish and a vacuum-tight crimped seal to ensure consistent, long-term performance. AAASTAND® brake boosters deliver significantly reduced pedal effort, consistent braking power assist, and a responsive, secure pedal feel. Available in single and tandem (dual) diaphragm configurations to match specific vehicle requirements.

Brake Booster Pump

AAASTAND® brake booster pumps are engineered using high-efficiency electric or mechanical drive motors, reinforced diaphragms, precision valves, and oil-resistant seals. low-noise motor assemblies, optimized vacuum chambers, and corrosion-resistant housings for stable negative-pressure generation. AAASTAND® booster pumps deliver rapid and consistent vacuum assist for brake boosters, ensuring enhanced braking force even under low manifold-vacuum conditions found in turbocharged engines, hybrid vehicles, and cold-start environments. Available in electric vacuum pumps, mechanical/vane-type pumps, integrated module pumps, and hybrid-vehicle booster pumps.

Brake Cable

AAASTAND® brake cables are engineered using high-tensile galvanized steel inner wires, multi-layer protective sheathing, and corrosion-resistant hardware. precision-wound stranded cores for smooth actuation, low-friction liners, and reinforced outer jackets to withstand abrasion, moisture, and road debris. AAASTAND® brake cables provide consistent and reliable actuation for parking brakes and rear mechanical brake systems. Available in rear parking brake cables, intermediate cables, front control cables, and complete multi-section assemblies.

Brake Caliper

AAASTAND® brake calipers meet SAE J431 standards and feature precision-machined cast iron or aluminum construction with anti-corrosion coating. Equipped with high-temperature phenolic pistons and EPDM rubber seals to ensure clamping force and disc brake performance. AAASTAND® brake calipers convert hydraulic pressure into mechanical clamping force for disc brake pad engagement. Engineered with integrated bleeder valves and dust boot protection to maintain hydraulic integrity while preventing contamination in front and rear disc brake systems.

Brake Disc

AAASTAND® brake discs use CNC-machined friction surfaces, balanced hub flanges, and heat-treated metallurgy to deliver stable braking, reduced noise, and improved thermal crack resistance. Coated and uncoated options include anti-corrosion Geomet® coating, paint-coated hats, and vented or solid rotor designs. AAASTAND® discs provide consistent stopping power, low vibration, and extended durability for passenger cars, SUVs, trucks, and commercial vehicles. Available in solid rotors, vented rotors, slotted rotors, drilled rotors, and high-carbon performance variants.

Brake Hose

AAASTAND® brake hoses are engineered using a multi-layer construction with a premium EPDM inner tube, high-tensile polyvinyl alcohol (PVA) braided reinforcement, and a durable EPDM outer cover. corrosion-resistant zinc-plated steel end fittings and pre-installed mounting brackets to ensure long-term durability and proper routing. AAASTAND® brake hoses deliver a firm pedal feel, consistent hydraulic pressure transfer, and superior resistance to abrasion, ozone, and common road chemicals. Available as individual lines and complete vehicle sets, including all necessary copper sealing washers.

Brake Hose

AAASTAND® brake hoses are engineered using multi-layer EPDM or SBR rubber, high-tensile braided fabric reinforcement, and zinc-plated steel fittings. precision-crimped end fittings, oil-resistant inner tubes, and abrasion-resistant outer jackets to ensure stable hydraulic pressure transmission and long-term durability. AAASTAND® brake hoses deliver consistent brake-fluid transfer for disc and drum braking systems, ensuring responsive and safe braking performance under varying temperatures and driving conditions. Available in front, rear, center, and extended-length off-road variants.

Brake Master Cylinder

AAASTAND® brake master cylinders are engineered to DOT 3/4/5.1 specifications, featuring precision-honed bore surfaces with anodized aluminum or cast iron construction. Dual-circuit safety systems with corrosion-resistant seals ensure consistent hydraulic pressure and fail-safe performance. AAASTAND® master cylinders convert pedal force into hydraulic pressure via piston assemblies. Dual-circuit design provides independent front/rear operation for safety redundancy. Integrated proportioning valve and compensating port technology maintain optimal brake fluid flow, prevent system over-pressurization.

Brake Pad

AAASTAND® brake pads use premium semi-metallic, low-metallic, or ceramic friction formulations. precision-molded backing plates, heat-resistant friction layers, and noise-reducing shims for quiet and stable braking response. Advanced friction compounds ensure consistent coefficient of friction (COF), reduced brake fade, and minimal rotor wear. AAASTAND® brake pads deliver reliable stopping power, low dust generation, and long service life for passenger cars, SUVs, and commercial vehicles. Available in ceramic, semi-metallic, and NAO formulations, with chamfered edges, slotted designs, and multi-layer rubber-steel-rubber shims.

Brake Shoe

AAASTAND® brake shoes are engineered using high-strength steel backing plates, premium bonded or riveted friction linings, and heat-resistant adhesives. precision-formed arcs for optimal drum contact, wear-resistant friction compounds, and corrosion-resistant coatings. AAASTAND® brake shoes provide consistent braking force, low noise, and long service life for rear drum brake systems on passenger cars, SUVs, pickups, and commercial vehicles. Available in bonded or riveted linings, asbestos-free friction materials, and complete sets with hardware kits.

Brake Wheel Cylinder

AAASTAND® brake wheel cylinders are engineered using high-strength cast iron or anodized aluminum bodies, precision-honed bores, and EPDM rubber cups. corrosion-resistant pistons, low-friction internal surfaces, and reinforced dust boots to ensure smooth hydraulic actuation and long-term sealing performance. AAASTAND® wheel cylinders deliver stable braking force distribution in drum-brake systems, ensuring consistent shoe expansion and reliable rear-axle braking performance. Available in single- and double-piston configurations, straight and angled inlet designs, and variants with integrated bleeder screws.

Brake Wheel Cylinder Repair Kit

AAASTAND® brake wheel cylinder repair kits are engineered using high-grade EPDM rubber cups, precision-cut seals, and corrosion-resistant pistons. includes dust boots, pressure cups, return springs, bleeder screws, and sealing washers that restore proper hydraulic sealing and piston movement. AAASTAND® repair kits restore braking efficiency for drum-brake wheel cylinders by ensuring smooth piston operation and long-term fluid sealing. Available for single-piston and dual-piston cylinder designs, with OE-style materials, bore diameters, and sealing geometries.

Others

AAASTAND® brake system hardware and mounting components are high-strength G3000 gray iron castings and premium stainless steel alloys. CNC-machined mounting surfaces, precision-stamped forms, and a corrosion-resistant coating. AAASTAND® braking components ensure proper caliper alignment, provide balanced friction surfaces, and eliminate brake noise and vibration for safe, consistent stopping power. The product portfolio includes brake drums, brake caliper mounting brackets, and complete brake hardware kits (including anti-rattle clips, springs, and guide pins).

Vacuum Pump Repair Kit

AAASTAND® vacuum pump repair kits use high-grade rubber seals, precision-cut gaskets, wear-resistant vanes, and lubrication-optimized components. includes oil-resistant O-rings, high-temperature membrane seals, corrosion-proof screws, and reinforced pump-cover gaskets to restore vacuum efficiency and long-term sealing performance. AAASTAND® repair kits restore proper vacuum output and operational stability for brake boosters, EGR controls, turbo systems, and engine-mounted mechanical vacuum pumps. Available for rotary-vane pumps, diaphragm pumps, and integrated vacuum-pump assemblies.